When I moved my US Tower 40' crank up from my last house to my current
residence, I needed a new wet-stamped set of plans for the base from a PE in
order to get a building permit. Rather than the square base specified by US
Tower, he designed a cylindrical base of dimensions that met mechanical
requirements, passed county approval and has worked fine for 9 years now.. You
might consider a professional design if you are going to substitute from
manufacturer's specs. A cylinder is easier to excavate with an augur compared
to digging a deep square hole.
Lee, KI7UR
Lee K. Brown MD
Clinical Professor of Internal Medicine andEmeritus Professor of Internal
MedicineDivision of Pulmonary, Critical Care, and Sleep MedicineUniversity of
New Mexico School of MedicineAssociate Editor and Founding Editor (“Emerging
Technology”), Journal of Clinical Sleep MedicineCo-editor, Section on Sleep and
Neurobiology, Current Opinion in Pulmonary MedicineChair, New Mexico Advisory
Board for Respiratory CareChair, Polysomnography Practice Advisory Committee of
the NM Medical Board
On Monday, March 25, 2024 at 02:21:21 PM PDT, Raymond Benny
<rayn6vr@gmail.com> wrote:
For my MA770 install, it called for a 3X3X7ft hole. Well, I rented a Bobcat
with a 12" auger and bored about 4 holes. I then went into the hole and
used an electric jack hammer and made it deeper and somewhat square.
Of course, I was 15 years younger then and was in better shape. But it
worked...
Ray,
N6VR/W7YA
Near Prescott, AZ
On Mon, Mar 25, 2024 at 8:28 AM jc-smith@comcast.net <jc-smith@comcast.net>
wrote:
> Hi Mike,
>
> I did exactly that same thing years ago. Used an auger to dig the base
> for my MA-550MDP. I also had the motorized raising fixture.
> Unfortunately, I'm away from home and don't have access to my plans/permit
> stuff. You'll probably hear from someone else about this but if not, keep
> in touch and I'll dig out my info when we get home.
>
> 73 - JC, K0HPS
> ________________________________
> From: TowerTalk <towertalk-bounces@contesting.com> on behalf of Mike
> Fatchett W0MU <w0mu@w0mu.com>
> Sent: Sunday, March 24, 2024 11:05 PM
> To: towertalk <towertalk@contesting.com>
> Subject: [TowerTalk] MA-550 Installation
>
> The tubular tower that I was looking for is actually a MA-550. The UST
> documents call for a hole 3x3x6 deep for the base. I would prefer to
> use a 36 inch auger. Has anyone done this? The hole would need to be
> 7.64 ft deep to account for the rounding of the corners to achieve the 2
> CU yards of concrete.
>
> I would like to motorize the tilt over feature to be used in the field.
> I am looking for recommendations.
>
> I you have other helpful hints I am all ears!
>
>
> Mike W0MU
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|