WriteLog
[Top] [All Lists]

Re: [WriteLog] CW Problems.

To: "'Gordon LaPoint'" <gordon.lapoint@gmail.com>, "'Ed W0YK'" <ed@w0yk.com>, "'WriteLog'" <writelog@contesting.com>
Subject: Re: [WriteLog] CW Problems.
From: "Don Hill AA5AU" <aa5au@bellsouth.net>
Date: Sun, 2 May 2021 11:52:23 -0500
List-post: <mailto:writelog@contesting.com>
I have the same issue. When set to PC generates CW and my normal COM port for 
CW, PTT keys all the time. No way to turn it off that I can find other than to 
select an unused COM port.

Don AA5AU

-----Original Message-----
From: WriteLog [mailto:writelog-bounces@contesting.com] On Behalf Of Gordon 
LaPoint
Sent: Sunday, May 2, 2021 9:58 AM
To: Ed W0YK; WriteLog
Subject: Re: [WriteLog] CW Problems.

Ed,
     Sorry, PTT keys and stays keyed (I have an LED on my home brew 
RS232 interface for CW/PTT/FSk, and the Radio is in TX, no CW sent 
unless I hit an F key, then it sends, but stays in TX)
CW Generation is "PC generates".
This hardware combination does work with N1MM and DXLabs for proper CW, 
with OR without PTT being used.  I normally run QSK so no PTT is 
normally used, but did test with the other software to insure my 
hardware is good.  I use the same RS-232 interface for RTTY with TXD for 
FSK and RTS for PTT. I de-select the port in rttyrite when doing CW to 
prevent conflicts.
Thanks,
Gordon - N1MGO

On 5/2/2021 10:30 AM, Ed W0YK wrote:
> Hi, Gordon.
>
> What does "keys and stays keyed" mean?  PTT or CW keying?  Which CW 
> generation method is selected in WL?
>
> 73,
> Ed W0YK
>
>
> -------- Original message --------
> From: Gordon LaPoint <gordon.lapoint@gmail.com>
> Date: 5/2/21 06:48 (GMT-08:00)
> To: WriteLog <writelog@contesting.com>
> Subject: [WriteLog] CW Problems.
>
> Hi,
>
>    I'm setup for the NEQP, SSB works fine.  when I switch to CW the
> radio keys and stays keyed, can not find what I have setup wrong.
>
> Radio - Kenwood TS590sg   Ports set to COM18 115200  - works fine,
> tracks radio frequency/mode
>
> CW - COM 7  DTR= CW  RTS= PTT
>
>
> CW Options:
>
> PTT Control (CW Mode ONLY)   None (QSK)   selected (tried "as specified
> in Ports", no difference)
>
> PTT to CW delay 0
>
> PC generates sends CW space on startup  - Checked  (also tried unchecked
> - no difference.
>
>
> What else should I check?
>
> This used to work, so don't know what changed except upgraded to 12.59F
> , so downgraded to 12.56c, no change.
>
>
> The same hardware setup works with N1MM and DX Labs, so I know the
> hardware is good!!!!
>
> Thanks,
>
> Gordon - N1MGO
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/


_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>