WriteLog
[Top] [All Lists]

Re: [WriteLog] Rotator Control

To: "'W7RY'" <w7ry@centurytel.net>, <ricp@alum.wpi.edu>
Subject: Re: [WriteLog] Rotator Control
From: "Ric Plummer" <ricp@charter.net>
Reply-to: ricp@alum.wpi.edu
Date: Wed, 21 Dec 2005 12:29:26 -0500
List-post: <mailto:writelog@contesting.com>
Jim
I have used these, BUT
the current version of the HELP file, under DCU-1
clearly states that no .ini entries affect that device.
So, I assumed that that was the final answer on that one.
Would be worth a try for which ever port Joe is using for the DCU-1,
but my suspision is that it won't control the port used by the DCU-1.
Guess only Wayne knows for sure
Happy Holidays to all the WL folks !!
Ric


-----Original Message-----
From: W7RY [mailto:w7ry@centurytel.net]
Sent: Wednesday, December 21, 2005 11:57 AM
To: ricp@ALUM.WPI.EDU
Cc: writelog@contesting.com
Subject: RE: [WriteLog] Rotator Control


Ric.

All of the baud rates are set in writelog.ini under the ports heading.
Here is a copy of my ports section from my writelog.ini file.

[PORTS]
dvktype=2
dvkport=4
cwtype=1
cwport=1
dvkstoploop=1
dvkechomic=1
Comm4RigManager={D0DE9422-0517-11D4-9D1B-00105AA43DDF}
Comm4XmitControl=ALWAYS
COM2:=9600,n,8,1
Comm3RigManager={D0DE9422-0517-11D4-9D1B-00105AA43DDF}
Comm3XmitControl=ALWAYS





As you can see, COM2 is set for 9600,n,8,1.

Make an entry just like this for your port and the baud rate you want.



73
Jim W7RY


-----Original Message-----
From: writelog-bounces@contesting.com
[mailto:writelog-bounces@contesting.com] On Behalf Of Ric Plummer
Sent: Wednesday, December 21, 2005 8:34 AM
To: 'Joseph Young'; writelog@contesting.com
Subject: Re: [WriteLog] Rotator Control

Joe,
>From the HELP file, in SutUp Ports:

DCU-1: the COMM port is set to 4800 baud, no parity, 8 bits, 1 stop bit.
No
INI settings affect this.

This explains the problem, but offers no 2400 baud solution

Ric KV1W


-----Original Message-----
From: writelog-bounces@contesting.com
[mailto:writelog-bounces@contesting.com]On Behalf Of Joseph Young
Sent: Wednesday, December 21, 2005 11:12 AM
To: writelog@contesting.com
Subject: [WriteLog] Rotator Control


Hello,
I am still fighting a rotator control problem with WriteLog. The
rotator is the C.A.T.S. DPU-1800d
and it responds correctly to the HyGain DCU-1 control character set,
but only at 2400 baud.
In WriteLog I have set up for the correct Com Port and the DCU-1
format. Then I go to the device
manager and force the baud rate to 2400 with the correct number of
data bits, start, stop, etc.
When I command the antenna to turn (Radio, Antenna to this azimuth
(Value)) the rotator control
unit does not receive the command to turn to (Azimuth). This is very
confusing because using
another logging program that allows the baud rate to be set directly
in the program (to 2400)
the controller works every time. I am missing something somewhere.
Thanks in advance for any ideas on this one.

73 de Joe, W6RLL



_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>