This is a multi-part message in MIME format.
------=_NextPart_000_0014_01C15564.DD05A5F0
Content-Type: text/plain;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
I did get Kam to work with Writelog. I too had a lot of difficutly
getting it to work but it does work. My guess is that you have the =
same
problem I had.
=20
Two things I would check: Is your Kam in Host mode? Is the baud rate
correct?
=20
Some things to consider:
If you power up the Kam while it is connected to writelog, do you see
the greeting that Kam provides when powering up? This will only occur
if you have the right baud rate and are NOT in host mode.
=20
If you do not see the message then you may have one of both of these
problems. =20
=20
If you use some other program with Kam, such as KaGold then set KaGold
to leave the tnc in a known state (say 2400 baud, host mode off. BTW,
this is a separate setting in KaGold. ) and then use this setting in
Writelog.
=20
Another possitbility, is to do a hard reset of Kam. I have not looked
at the manual recently, but there may be a jumper on the board to do
this. =20
=20
Regards,
Rajiv, N2RD
=20
=20
=20
----- Original Message -----=20
From: Rsauvan <mailto:cabmas@bankpds.com> =20
To: writelog@contesting.com <mailto:writelog@contesting.com> =20
Sent: Sunday, October 14, 2001 9:57 PM
Subject: [WriteLog] rtty cable
Hi all,
Still trying to get something to work on rtty with WLog. Havent =
been
able to get the Kam to receive data yet. Dont know what else to do. So
am going for the afsk hook-up to sound card.Have yet to figure out =
which
pins on the acc2
plug in the back of my 850 to hook the sound card too. Ive tried a
couple of them only to find they key the rig as soon as they are
plugged. Can someone tell me which pins to hook up to so I can get some
rtty going? This would be for the tx cable only, I was smart enough to
figure out the receive one believe it or not.
Thanks-Bob-WT9Q
------=_NextPart_000_0014_01C15564.DD05A5F0
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META content=3D"MSHTML 6.00.2526.0" name=3DGENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=3D#ffffff>
<DIV><FONT face=3DArial size=3D2>I did get Kam to work with =
Writelog. I too=20
had a lot of difficutly getting it to work but it =
does work. My=20
guess is that you have the same problem I had.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Two things I would check: Is =
your Kam in Host=20
mode? Is the baud rate correct?</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Some things to consider:</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>If you power up the Kam while it is =
connected to=20
writelog, do you see the greeting that Kam provides when powering =
up? This=20
will only occur if you have the right baud rate and are NOT in host=20
mode.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>If you do not see the message then you =
may have one=20
of both of these problems. </FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>If you use some other program with =
Kam, such as=20
KaGold then set KaGold to leave the tnc in a known state (say 2400 =
baud, host=20
mode off. BTW, this is a separate setting in KaGold. ) and =
then use=20
this setting in Writelog.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Another possitbility, is to do a hard =
reset of=20
Kam. I have not looked at the manual recently, but there may be a =
jumper=20
on the board to do this. </FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Regards,</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>Rajiv, N2RD</FONT></DIV>
<DIV> </DIV>
<DIV> </DIV>
<DIV> </DIV>
<DIV>----- Original Message ----- </DIV>
<BLOCKQUOTE dir=3Dltr=20
style=3D"PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; =
BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV=20
style=3D"BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: =
black"><B>From:</B>=20
<A title=3Dcabmas@bankpds.com =
href=3D"mailto:cabmas@bankpds.com";>Rsauvan</A>=20
</DIV>
<DIV style=3D"FONT: 10pt arial"><B>To:</B> <A =
title=3Dwritelog@contesting.com=20
href=3D"mailto:writelog@contesting.com";>writelog@contesting.com</A> =
</DIV>
<DIV style=3D"FONT: 10pt arial"><B>Sent:</B> Sunday, October 14, 2001 =
9:57=20
PM</DIV>
<DIV style=3D"FONT: 10pt arial"><B>Subject:</B> [WriteLog] rtty =
cable</DIV>
<DIV><BR></DIV>
<DIV><FONT face=3DArial size=3D2>Hi all,</FONT></DIV>
<DIV><FONT face=3DArial size=3D2> Still trying to =
get something=20
to work on rtty with WLog. Havent been able to get the Kam to receive =
data=20
yet. Dont know what else to do. So am going for the afsk hook-up to =
sound=20
card.Have yet to figure out which pins on the acc2</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>plug in the back of my 850 to hook =
the sound card=20
too. Ive tried a couple of them only to find they key the rig as soon =
as they=20
are plugged. Can someone tell me which pins to hook up to so I can =
get some=20
rtty going? This would be for the tx cable only, I was smart enough =
to figure=20
out the receive one believe it or not.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2> =
=20
=
=20
=
=20
=20
Thanks-Bob-WT9Q</FONT></DIV></BLOCKQUOTE></BODY></HTML>
------=_NextPart_000_0014_01C15564.DD05A5F0--
|