Towertalk
[Top] [All Lists]

Re: [TowerTalk] Heliax question

To: towertalk@contesting.com, John Simmons <jasimmons@pinewooddata.com>
Subject: Re: [TowerTalk] Heliax question
From: "J. Hunt via TowerTalk" <towertalk@contesting.com>
Reply-to: "J. Hunt" <ki5dq@yahoo.com>
Date: Sun, 25 Jul 2021 00:33:43 +0000 (UTC)
List-post: <mailto:towertalk@contesting.com>
 Hi John,

Moisture within any feedline is trouble - moisture will cause corrosion / 
oxidization.
These conditions will build resistance / impedance problems within feedlines / 
terminations.

At higher power levels, moisture can cause RF arcing.

Many professional installations, Heliax is slightly pressurized with N2 to keep 
moisture out.

Appreciate the inquiry.

Thanks n 73,
James
KI5DQ 


     On Saturday, July 24, 2021, 07:23:16 PM CDT, John Simmons 
<jasimmons@pinewooddata.com> wrote:  
 
 James,

"Moisture within any feedline is trouble"

How does this manifest itself?

-- 
73,
-de John NI0K rural Debs, MN

J. Hunt via TowerTalk wrote on 7/24/2021 7:13 PM:
>  
> Visible "conductor are oxidized, stained or tarnished" is bad news, highly 
> suspect remaining moisture within.
>
> Moisture within any feedline is trouble.
>
> Thanks n 73,
> James
> ki5dq
>
>      On Saturday, July 24, 2021, 12:36:08 PM CDT, Jon Zaimes via TowerTalk 
><towertalk@contesting.com> wrote:
>  
>  Two tests I use for newly acquired used hardline .....
> With nothing connected to the other end, measure resistance with VOM. It 
> should be open. Anything else, there is a problem.
> Then I test with the TDR function on my AA-230 Zoom antenna analyzer. 
> Normally two flat lines near center scale but if a problem it will show 
> otherwise. It may show distance to a specific fault.
> 73/Jon
>
> Jon P. Zaimes, AA1K Tower climber for hire http://www.aa1k.us/ Cell: 
> 302-632-2353email: jz73@verizon.net or aa1k@arrl.net
>
> -----Original Message-----
> From: trentkd5ia--- via TowerTalk <towertalk@contesting.com>
> To: towertalk@contesting.com <towertalk@contesting.com>
> Sent: Sat, Jul 24, 2021 1:30 pm
> Subject: [TowerTalk] Heliax question
>
> I have a length of 1 5/8” air dielectric Heliax.  When I cut it to install a 
> connector, the outside surface of the inner conductor and both inside and 
> outside surfaces of the outer conductor are oxidized, stained or tarnished.  
> So, is it usable or am I just wasting my time working on it?
> Thanks and 73 de Trent  K5XM
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>    
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
  
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>