Re: [TenTec] TT omni vii if port problems

[Bob McGraw K4TAX <rmcgraw@blomand.net>]

Even as a 2nd receiver, it is limited by the band pass filters in the 
front end of the Omni VII.    As to using it in the IF, there is only 
about 2 MHz BW available from center frequency.  I agree, using a dongle 
at the IF stage is a cheap way to get a panadapter.   But to get full 
range coverage and to get a 2nd receiver, the SDR play working off of 
the band pass filter output allows one to work one band with the radio 
and listen to another band at the same time.    Can't do that with a 
dongle off of the IF.
73
Bob, K4TAX


On 8/30/2018 6:19 PM, Greg S via TenTec wrote:
> Yes, but it can tune much HIGHER. Just so limiting using it as an I. F. Monitor 
> only, in my eyes.
> Strokes for folks, I guess.
> Good luck getting it all sorted out.
> Greg, KC8HXO
> --------------------------------------------
> On Thu, 8/30/18, Bob McGraw K4TAX <rmcgraw@blomand.net> wrote:
>
>   Subject: Re: [TenTec] TT omni vii if port problems
>   To: tentec@contesting.com
>   Date: Thursday, August 30, 2018, 6:39 PM
>   
>   Largely because the dongle being
>   used does not tune below or have
>   adequate
>   sensitivity below about 20 to 25 MHz.    The IF in the
>   Omni VII
>   is about 70 MHz.
>   
>   73
>   
>   Bob, K4TAX
>   
>   
>   On 8/30/2018 3:31 PM, Greg S via TenTec
>   wrote:
>   > I highly recommend this mod, to
>   allow full use of the SDR. Not sure why anyone would use the
>   I.F. these days, honestly.
>   > Greg,
>   KC8HXO
>   >
>   --------------------------------------------
>   > On Thu, 8/30/18, Bob McGraw K4TAX <rmcgraw@blomand.net>
>   wrote:
>   >
>   >   Subject:
>   Re: [TenTec] TT omni vii if port problems
>   >   To: tentec@contesting.com
>   >   Date: Thursday, August 30, 2018, 12:59
>   PM
>   >
>   >   Do you
>   have any application
>   >   associated with
>   the device controlling the
>   >   radio?
>   Also, if you are tuning to a signal
>   >
>   using the dongle, it may be
>   >
>   incorrect with
>   >   regard to frequency
>   thus this puts the Omni VII off
>   >
>   frequency.     You may need to perform a
>   >   Master Reset on the Omni VII.
>   >   There are
>   >   known
>   some software applications which do shift the VFO,
>   >   although not displayed as such on the
>   radio.
>   >   This will produce and off
>   >   frequency
>   >
>   condition.
>   >
>   >
>   I had a a 3
>   >   Rivers Dongle on my Omni
>   VII and it worked OK.   The
>   >
>   software was a major pain in the posterior to
>   >   get running correctly.
>   >   Finally I
>   >   wrote
>   it off as a learning experience.   I then purchased
>   >   an
>   >   SDR Play
>   RSP-1 receiver and downloaded
>   >   free
>   HDSDR software.  All issues
>   >
>   resolved
>   >   and it works great.
>   >
>   >   I also
>   >   made the mod to the Omni VII for the
>   2nd receiver which I
>   >   find
>   >   works even better.  With the SDR
>   Play
>   >   I can see signals on the
>   entire
>   >   band, thus
>   >   not limited to the IF bandwidth.  That
>   works great as
>   >   well.
>   >
>   >   73
>   >
>   >   Bob, K4TAX
>   >
>   >
>   >   On 8/30/2018 11:17 AM, denton
>   >   sprague wrote:
>   >
>   > Hi all…I installed an
>   >   if port
>   output as per 3 rivers TT omni vii dongle
>   >   instructions to enable me to use a pc
>   as a spectrum monitor.
>   >   it works fine
>   on receive but the minute I transmit, am told
>   >   I am off frequency.
>   >   > I am thinking of
>   >   either installing a relay that will
>   disconnect the
>   >   dongle’s if input
>   during transmit…
>   >   >
>   >   Anyone else have a different work
>   around?
>   >   >
>   >
>   _______________________________________________
>   >   > TenTec mailing list
>   >   >
>   >   TenTec@contesting.com
>   >   > http://lists.contesting.com/mailman/listinfo/tentec
>   >
>   >
>   >
>   _______________________________________________
>   >   TenTec mailing list
>   >   TenTec@contesting.com
>   >   http://lists.contesting.com/mailman/listinfo/tentec
>   >
>   >
>   _______________________________________________
>   > TenTec mailing list
>   >
>   TenTec@contesting.com
>   > http://lists.contesting.com/mailman/listinfo/tentec
>   
>   
>   _______________________________________________
>   TenTec mailing list
>   TenTec@contesting.com
>   http://lists.contesting.com/mailman/listinfo/tentec
>   
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec