TenTec
[Top] [All Lists]

Re: [TenTec] Corsair II & Omni V Filters

To: Tentec@contesting.com
Subject: Re: [TenTec] Corsair II & Omni V Filters
From: "Gary Smith" <Gary@doctorgary.net>
Reply-to: Gary@doctorgary.net,Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 27 Nov 2007 03:02:21 -0500
List-post: <mailto:tentec@contesting.com>
Hi all,

My Dad was always nondescript and figuring out his old radio is much 
of the same. I took off the covers and looked at the filters and 
sonofagun, every bay is filled. I have no idea what is in the 9 Mhz 
optional slot as there's no name on it relating to a model of filter. 


As SSB was his interest I assume it's a 1.8 or 2.4 filter, nothing on 
the filter saying what it is though.

The rig seems to have a problem; the VFO A light does not light up 
and if I hold the "rev" in while changing freq it does nothing. The 
only way I have seen the "rev" button have an effect is if I have 
VFO B and split enabled. If I do so and move the VFO, when I press 
"rev, it shows the earlier frequency. 

If I am in what I suspect is the "VFO A" condition (default position 
but no LEDs saying "VFO A) and then I depress & hold the rev button 
and then move the vfo, the frequency changes but If I release the 
"rev" button, it does not snap back to the original frequency; it's 
like the rev button has no effect unless split is engaged.

According to the "offset tuning" data in 3-1.6 it should return to 
the "target" frequency but it does not.

Ideas?

Thanks!

Gary

P.S.; I really thank you for all the unselfish help when I've reaqlly 
needed it.

> Gary:
> 
> The TenTec Wiki is the best place for this ... all the info in one 
> table (including the stock code for when the filter has no other 
> markings!).
> 
> <http://tentecwiki.org/doku.php?id=filters>
> 
> You can see the Models 282, 285 and 288 are 6.3MHz filters.
> 
> The Model 216 through 221 are the 9MHz
> 
> INRAD are also a good source of info (they make filters) for which IF 
> is which:
> 
> <http://www.qth.com/inrad/tentec_menu.htm>
> 
> The Cosair II will only accept extra 6.3MHz filters.
> 
> The Omni V can use both 9MHz and 6.3MHz filters.
> 
> The other Omni V users here can recommend the optimal setup (though I 
> suspect that would be matching 9MHz and 6.3MHz filters for PBT to 
> work best and 9MHz would be closer to the mixer so they would be 
> preferred first).
> 
> <http://tentecwiki.org/doku.php?id=562>
> 
> 73 Kevin N7WIM
> 
> On Nov 26, 2007, at 11:55 AM, Tony Berg wrote:
> 
> > Gary,
> >
> > According to a "Ten-Tec Instruction Sheet for Models 282, 285 and
> > 288 Crystal Filters," they are designed for use in the Omni V,
> > Paragon, Corsair and Corsair II transceivers. These are for the 6.3
> > Mhz IF. Per another instruction sheet, the 217 and 219 that you
> > mentioned are for the Omni V (and other listed units, but not the
> > Corsair II) 9 MHz IF.
> >
> > 73,
> > Tony W1OT
> >
> > On 11/26/07, Gary Smith <Gary@doctorgary.net> wrote:
> >> Looks like my Corsair II is going to be my backup rig. I'm getting
> >> ahold of my father's Omni V which has been mothballed for years.
> >>
> >> I have a couple questions in light of this;
> >>
> >> Looking at the old brochures, I see the CW crystal filters are
> >> different numbers between the Corsair II & the V, are they
> >> interchangeable though?
> >>
> >> I have the model 285 500Hz & the model 282 250Hz filters (no 288
> >> SSB filter) and see the V calls for model 217 for 500Hz & a 219 for
> >> 250Hz
> >>
> >> If the Corsair filters can be placed successfully in the Omni, that
> >> would sure be nice.
> >>
> >> Thanks,
> >>
> >> Gary
> >> ka1j
> --
> 73 DE N7WIM / G8UDP
> Kevin Purcell
> kevinpurcell@pobox.com
> 
> 
> 
> 


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>