TenTec
[Top] [All Lists]

RE: [TenTec] Orion Question

To: Rick@dj0ip.de, tentec@contesting.com
Subject: RE: [TenTec] Orion Question
From: Eric Scace K3NA <eric@k3na.org>
Reply-to: eric@k3na.org, tentec@contesting.com
Date: Wed, 04 Feb 2004 22:43:26 -0500
List-post: <mailto:tentec@contesting.com>
Hi Rick --

   I wasn't suggesting using an antenna switch to connect the antenna analyzer 
or the radio to the tuner.  As you pointed out, many
switches have inadequate isolation.  What I had done in the past was disconnect 
the coax from the back of the transceiver and
connect that coax to the antenna analyzer.

-- Eric

-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On Behalf Of Rick Westerman
Sent: 2004 February 4 10:07
To: eric@k3na.org; tentec@contesting.com
Subject: RE: [TenTec] Orion Question


Sorry Eric, NOT a good reply.

In fact that's a good way to blow out MFJ 259's.
(been there, done that)

I also tune the linear with low power (here 15 or 20w wouldn't
matter).
I can't tune the linear, driving it from the MFJ.

Years ago I connected my MFJ 259 via an SPDT coax switch and did
just what you suggest.
The result was in a very short time the MFJ was dead.
Apparently there wasn't enough isolation in the switch.
Since then I always remove it completely from the feedline before
applying power.

What I do though, is periodically tune the matchbox on all bands
using the MFJ-259B and create a table of pre-sets.
Then I remove the MFJ and after each band change, set to the
matchbox to the table's pre-set values and then apply low power
to fine tune.  My wish is for 15w out when I press the "TUNE"
button.

Thanks anyway.

73
Rick




-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On Behalf Of Eric Scace
K3NA
Sent: Wednesday, February 04, 2004 4:52 PM
To: Rick@dj0ip.de; tentec@contesting.com
Subject: RE: [TenTec] Orion Question


   If you have an antenna analyzer like the AEA or MFJ units, the
best way to tune your matchbox is to connect the antenna
analyzer.
These analyzers put out about 1 mW and you can see exactly the
impedance.  Note the settings for each band (or frequency within
a
band).  Then hook up your radio and go -- no need for further
tweaking.

-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On Behalf Of Rick Westerman
Sent: 2004 February 4 09:36
To: tentec@contesting.com
Subject: [TenTec] Orion Question


Is it possible to change the output power of the "TUNE" button
from 20w to 15w?

My watt meter peaks at 15w or 150w.
It would be nice to have just 15w for matchbox tuning purposes.

Tnx.

73
Rick


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>