TenTec
[Top] [All Lists]

[TenTec] Jupiter Suggestions

To: <tentec@contesting.com>
Subject: [TenTec] Jupiter Suggestions
From: malonej@c2i2.com (Jack Malone)
Date: Thu, 5 Apr 2001 14:07:31 -0700
Jim:
More info on speaker. I finally got mine the way I want it by using  two
Radio Shack Line Transformers. These completely isolate the input.

Hook up as follows Jupiter to C and 4ohm on the first xformer, then C and
1.25 watt from first to second, then C and 8ohm on second, this assumes you
have 8ohm speaker if not use the tap for your speaker impedance.

The reason I used 4ohm tap on first xformer is the TT specs call for 4ohm
output. Now you can ground the C on the second xformer with no problem. This
makes it compatible with everything that I know of.

It works great on my NVA319 speaker that I use with my JRC NRD545DSP
Receiver. This speaker has the option of selecting either speaker 1 or 2.
The JRC545 uses grounded output to the NVA319 and by mounting my 2 xformers
inside the cabinet and feeding the TT to my second speaker input on NVA319
through the xformers and then into the speaker selection switch and it's 2
hi cut filters & 1 lo cut filter everything works great.
The NRD545 is on a very long wire antenna and this setup allows me to switch
between the TT & 545 when I get a very weak station that I cannot copy on
the TT.
73's
Jack, W7EJJ
--
----- Original Message -----
From: <pywacker@fuse.net>
To: "Jack Malone" <malonej@c2i2.com>
Sent: Monday, April 02, 2001 6:45 PM
Subject: Re: [TenTec] Jupiter Suggestions


> Jack, thanks for info.
>
> 73 de KE4WY Jim
>
> ----- Original Message -----
> From: "Jack Malone" <malonej@c2i2.com>
> To: <pywacker@fuse.net>
> Cc: "Ten-Tec" <tentec@contesting.com>
> Sent: Monday, April 02, 2001 9:40 PM
> Subject: Re: [TenTec] Jupiter Suggestions
>
>
> > Hi Jim:
> >
> >     My biggest complaint with the Jupiter is the speaker output, they
use
> a
> > push/pull output that cannot be grounded. Cheap way of doing it, Drake
did
> > the same thing on their SW-8. This negates using my external speaker
which
> > has two input positions on it. I use one input for my JRC NRD545DSP
> Receiver
> > and would like to use the other for the Jupiter but cannot. I bought a
> > $19.95 speaker from Radio Shack, in the meantime I'm going to try some
> > isolation methods and try to isolate the Jupiter speaker out. Capacitors
> > will not work.
> >
> >     I use a transmit bandwidth of 2550 or 2400 just to keep my sig from
> > QRMing adjacent freqs.
> >
> >     Mic gain depends on mic. I use a Radio Shack Pro 301 dynamic studio
> mic
> > with gain at 100% and R72 on the logic board set full gain. When I use
the
> > TenTec 701 hand mic I set the mic gain to about 5 to 20%
> >
> >     I use 60% processor.
> >
> >     I run about 400Watts PEP with a Amp.
> >
> > 73's
> > Jack, W7EJJ
> > w7ejj@arrl.net
> >
> > ----- Original Message -----
> > From: <pywacker@fuse.net>
> > To: "TenTec Mailing List" <tentec@contesting.com>
> > Sent: Monday, April 02, 2001 1:31 PM
> > Subject: [TenTec] Jupiter Suggestions
> >
> >
> > >
> > > Any suggestions on a good external speaker for the Jupiter? The
internal
> > > speaker is surprisingly quite good.
> > >
> > > Also on phone I would be curious to know the transmit bandwidth,
> > processing
> > > or not, typical mic gain settings and microphone Jupiter users are
> using.
> > > If you would share this in private email I would appreciate this info.
> > >
> > > 73 de KE4WY Jim
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > --
> > > FAQ on WWW:               http://www.contesting.com/FAQ/tentec
> > > Submissions:              tentec@contesting.com
> > > Administrative requests:  tentec-REQUEST@contesting.com
> > > Problems:                 owner-tentec@contesting.com
> > >
> > -
> > end
> >
>
>
>


--
FAQ on WWW:               http://www.contesting.com/FAQ/tentec
Submissions:              tentec@contesting.com
Administrative requests:  tentec-REQUEST@contesting.com
Problems:                 owner-tentec@contesting.com


<Prev in Thread] Current Thread [Next in Thread>